Industrial
25L Stackable Plastic Jerrycan
F21-IP-25L-ring stackable HDPE jerrycan, 25 litres, natural. The industrial workhorse for decanting, storage and distribution.
Product code F21-IPG-05 / -10 / -20 / -25 / -30
Natural, untinted HDPE for food, beverage and potable use. The declaration covers the cap and liner as well as the body, because that is where food-contact claims usually fail.
| Product code | F21-IPG-05 / -10 / -20 / -25 / -30 |
|---|---|
| Capacities | 5, 10, 20, 25 and 30 litres |
| Material | Natural HDPE, food-contact grade |
| Intended contents | Food, beverage, potable water and food-industry ingredients |
| Form factor | Stackable, L-ring |
| Colour | Natural translucent, so the level is visible |
| Neck | DIN 45, 51 or 61 |
| Lead time | Approximately one month for a standard production run; samples in 7–15 days. Confirmed against your specification at quotation. |
These depend on your order, your market or the certificate that covers your run, so we quote them rather than publish one figure that would be wrong for most buyers. Ask and you get the number for your specification.
Before you order: Food-contact compliance is per destination market and covers the closure and gasket as well as the body. Confirm the declaration you need before ordering.
A food-grade body with an unspecified cap liner is not a food-grade container. The declaration has to cover the closure and the gasket.
Natural HDPE lets an operator read the level without opening the can, which matters when opening it is the contamination risk.
Food-contact rules are national, not global. Tell us the destination and we will tell you which declaration applies.
This line is sold for food and potable use only. It is not a general chemical can in a lighter colour.
The same breakdown our distributors put in front of their own buyers.
The can is blow-moulded from high-density polyethylene in a single seamless wall, with the neck and handle formed in the same shot, so there is no seam to split under load. The resin is a food-contact grade run on a line kept clear of recycled regrind. Moulding runs across our Vietnam and China plants under one specification managed from Singapore.
Every can is checked before it leaves the plant:
Water is not a dangerous good, so no UN transport marking applies.
Food, beverage, potable water and food-industry ingredients
Fuels unless the can is fluorinated, and any chemical you have not had confirmed.
Send us the exact liquid, its concentration and its temperature and we confirm it against a compatibility check before you order.
Related guides: Chemical compatibilityUN packaging codes explained
The regimes that apply to this type of container in each market we ship to, with the detail behind each one a click away. This is what the market asks for; what this particular design already holds is in the specification above.
Orientation for specification, not legal advice, and not a statement that this design holds a given approval. Requirements turn on the exact design, contents and destination, and they change. Tell us the market at enquiry and we confirm what applies to your specification, what we hold and what we would need to obtain.
Yes, this line is natural HDPE specified for food contact, with the wetted path chosen for food use rather than assumed. It is made for food, beverage, potable water and food-industry ingredients.
It should, and that is the point to confirm, since food-contact compliance covers the closure and gasket as well as the body. Tell us the declaration you need and we confirm the full wetted path before you order.
It is specified for food contact, not built as a dual-use chemical can, so we would steer chemical duty to the industrial or fluorinated lines. Send us the substance and we point you to the right can and a compatibility check.
It suits a wide range of food, beverage and ingredient liquids, but strong or hot ingredients still depend on the specific product and temperature. Tell us what you are packing and we confirm it.
HDPE resists many food acids, but suitability depends on the concentration and temperature involved. Send us the exact ingredient and we check it against a compatibility check rather than assume it.
Water-based food and beverage liquids do not permeate HDPE the way fuels and solvents can. If your product carries strong volatile aromas or oils, tell us and we advise on the right specification.
Food-grade and UN dangerous-goods approval are separate questions, and food liquids are usually not dangerous goods, so a UN rating is not normally the point here. Confirm your contents and destination with us and we tell you what applies.
Clean HDPE can be reused for food duty with proper cleaning, and it carries a service life from its date of manufacture. Ask us for the manufacturing date and the food-contact reuse guidance for your market.
The natural translucent wall is deliberate, so you can read the fill level, and we can still mould it in a colour and add in-line marking for private-label programmes. It comes in 5, 10, 20, 25 and 30 litre with a DIN 45, 51 or 61 neck.
Minimum order and lead time come on quotation. The cans are moulded in Vietnam and China and managed from our Singapore desk, and HDPE is resin code 2 and recyclable when clean.
L-ring stackable HDPE jerrycan, 25 litres, natural. The industrial workhorse for decanting, storage and distribution.
Empty HDPE cans for diesel exhaust fluid, 10 and 20 litre, blue cap, with a misfueling-resistant spout. Packed by the carton.
Barrier-treated HDPE for solvents, agrochemicals and hydrocarbons. The fluorinated interior stops permeation and the panelling that follows it.
Carbon-loaded conductive HDPE for flammable liquids, where static build-up on an insulating wall is the hazard.
The same stackable body without a dangerous-goods approval, for non-hazardous liquids. Faster to supply and materially cheaper.
Removable-head HDPE for pastes, powders, gels and viscous product that will not pour through a narrow neck.
Tell us your destination market, target volumes and whether you need private labelling.